Get Started
Use AI properly

Mission 11 of 11

Fix your slow internet with Claude: find the real cause in 5 minutes

Slow internet is usually one boring fault: a bad cable, the wrong WiFi band, a crowded channel, slow DNS, or Windows quietly using your connection. This free course gives you the exact prompt from our reel.

20 minBeginnerFree with the copy and paste routeFree mission

What you'll do

The exact prompt from the reel, ready to copy
A real before and after speed test, so you know whether anything changed
A plain-English diagnosis of your own cable, WiFi band, channel, DNS, background use and power saving
  • The fix for each cause, and how to undo every one of them
Before you start
  • A Windows 10 or 11 PC. The checks in this course are Windows commands
  • Either Claude Code (needs a paid Claude plan) or any free AI chat such as Claude, ChatGPT or Gemini
  • About 20 minutes. No coding
Your progress0/7
01/07What happened in the reel0 done
STEP 01 of 07~2 min

What happened in the reel

See the real case this course is built on, so you know what a good result looks like.

  1. The reel is based on a post in the Claude community on Reddit: Claude helped me make my internet 100x faster ↗. The author's connection had been slow for days. A speed test showed 4.54 Mbps down and 8.26 Mbps up.

  2. They asked Claude Code to check what was wrong. Claude looked at the network card and found the wired connection running at 10 Mbps, on a card built for 2.5 Gbps. Nothing in software was forcing it, and there were no errors, which points to one thing: a damaged or low-grade Ethernet cable.

    Our recreation of that session for the reel. The commands are real and the numbers are the ones in the Reddit post.
  3. They swapped the cable. The link jumped to 1 Gbps, and the next speed test showed 799.02 Mbps down and 519.53 Mbps up.

    Tip
    That result is theirs, not a promise. A jump that big only happens when something was badly broken. If your connection is healthy, the same checks will tell you so, and that is useful too: it means the problem is your router or your provider, not your PC.
Checkpoint
You know the story: a slow connection, one prompt, a 10 Mbps cable found, and a real speed test before and after.
Stuck? Ask the community
STEP 02 of 07~2 min

Measure your speed first

Get a real number before you change anything, or you'll never know what helped.

  1. Open speedtest.net ↗ or fast.com ↗ in your browser and run the test.

  2. Write down three numbers: download, upload and ping.

  3. Find the speed you pay for. It's on your bill or in your provider's app.

    • Close to what you pay for? Your connection is fine. Slow pages are more likely one device, one website, or WiFi in one room.
    • Far below what you pay for? Carry on. That gap is what the checks are for.
    Tip
    Using a VPN? Run the test once with it on and once with it off. A VPN sends everything through another server, so it's one of the most common reasons a fast line feels slow.
Checkpoint
You have your download, upload and ping written down, and you know the speed you pay for.
Stuck? Ask the community
STEP 03 of 07~1 min

Pick your route

Choose between the hands-off route and the free route. Both run the same checks.

    • Route A, Claude Code. Claude runs the checks itself, reads the results and offers the fixes. You approve each action. It needs a paid Claude plan. If you've never used it, Claude Code for complete non-coders installs it from nothing in about six minutes.
    • Route B, free. You paste one block of commands into PowerShell, then paste the report into any free AI chat. It takes two extra minutes and costs nothing.
  1. Do step 4 for Route A or step 5 for Route B, then meet back at step 6.

Checkpoint
You know which route you're taking.
Stuck? Ask the community
STEP 04 of 07~4 min

Route A: give Claude Code the prompt

Let Claude run the checks on your PC while you stay in control of every action.

  1. Open a terminal. Press Win + X and choose Terminal or Windows PowerShell.

  2. Start Claude Code in manual mode, so it asks before it does anything.

    Terminal
    claude --permission-mode manual
  3. Paste this prompt and press Enter.

    The prompt
    My internet is slow. Find out why, then help me fix it.
    
    Work through these checks in order and tell me what you find at each one in plain English:
    
    1. Link speed: what speed is my network adapter actually connected at (Ethernet and WiFi), and what speed does the adapter support? A wired link stuck at 10 or 100 Mbps on a faster card usually means a bad cable or port.
    2. WiFi: am I on the 2.4 GHz band or on 5 or 6 GHz, how strong is my signal, and how many nearby networks share my channel?
    3. DNS: how long does a lookup take with my current DNS server, compared with 1.1.1.1?
    4. Background use: is Windows sharing updates with other PCs, and is a VPN or proxy switched on?
    5. Power saving: is my WiFi adapter set to save power?
    6. Errors: are there packet errors or discards on the adapter?
    
    Then give me a short list of what is wrong, most likely cause first, with the fix for each one.
    
    Rules: only run commands that read information until I say otherwise. Do not change any setting until you have told me what it does and how to undo it, and I have said yes. If a fix is physical (a cable, moving the router, a router setting), tell me exactly what to do myself.

    Claude will ask permission to run commands. The ones that only read information start with Get-, netsh wlan show or powercfg /q. Those are safe to approve.

    Warning
    If a command starts with Set-, netsh ... set, powercfg /set or Disable-, it changes something. Read what Claude says it does, and only say yes if you understand it and it has told you how to undo it.

    After a minute or so you'll get a short list: what's wrong, most likely first, and the fix for each.

Checkpoint
Claude has given you a list of findings in plain English, and you haven't approved any change you didn't understand.
If it breaksIt says 'claude' is not recognized + 1 more
It says 'claude' is not recognized
Claude Code isn't installed yet. Follow step 1 of Claude Code for complete non-coders, or use Route B.
It asks for administrator rights
The checks don't need them. Changing some settings does. If Claude needs admin for a fix, it's easier to make that change yourself with the steps in step 7.
Still stuck? Ask the community
STEP 05 of 07~4 min

Route B: the free check

Run the same checks yourself with one paste, and let a free AI read the report.

  1. Press Win + X and choose Terminal or Windows PowerShell, not the one marked Admin.

  2. Copy this whole block, paste it in and press Enter. It only reads information. The one thing it touches is your DNS cache, which it clears so the timing is fair, and Windows rebuilds that by itself.

    Windows PowerShell
    "--- 1. Link speed"; Get-NetAdapter | Where-Object Status -eq 'Up' | Format-List Name, InterfaceDescription, LinkSpeed
    "--- 2. WiFi"; netsh wlan show interfaces | Select-String "Band|Channel|Radio type|Receive rate|Transmit rate|Signal"
    "--- 3. Networks on each channel"; netsh wlan show networks mode=bssid | Select-String "^\s+Channel\s+:" | ForEach-Object { ($_ -split ':')[1].Trim() } | Group-Object | Sort-Object { [int]$_.Name } | Format-Table Name, Count -AutoSize
    "--- 4. DNS lookup time"; Clear-DnsClientCache; "Your DNS: " + [math]::Round((Measure-Command { Resolve-DnsName example.com -DnsOnly }).TotalMilliseconds) + " ms"; "1.1.1.1:  " + [math]::Round((Measure-Command { Resolve-DnsName example.org -Server 1.1.1.1 -DnsOnly }).TotalMilliseconds) + " ms"
    "--- 5. Windows update sharing"; Get-DeliveryOptimizationPerfSnap | Format-List DownloadMode, NumberOfPeers
    "--- 6. WiFi power saving (0 means off)"; powercfg /q SCHEME_CURRENT 19cbb8fa-5279-450e-9fac-8a3d5fedd0c1 12bbebe6-58d6-4636-95bb-3217ef867c1a | Select-String "Current"
    "--- 7. Errors"; Get-NetAdapterStatistics | Format-List Name, ReceivedPacketErrors, ReceivedDiscardedPackets

    This is the real report from our own Windows 11 laptop on 12 November 2026:

    Output
    --- 1. Link speed
    
    Name                 : ProtonVPN
    InterfaceDescription : WireGuard Tunnel
    LinkSpeed            : 100 Gbps
    
    Name                 : WiFi
    InterfaceDescription : Intel(R) Wi-Fi 6E AX211 160MHz
    LinkSpeed            : 585 Mbps
    
    --- 2. WiFi
    
        Band                   : 5 GHz
        Channel                : 36
        Radio type             : 802.11ac
        Receive rate (Mbps)    : 468
        Transmit rate (Mbps)   : 585
        Signal                 : 82%
    --- 3. Networks on each channel
    
    Name Count
    ---- -----
    1        1
    3        1
    11       1
    36       1
    
    --- 4. DNS lookup time
    Your DNS: 33 ms
    1.1.1.1:  18 ms
    --- 5. Windows update sharing
    
    DownloadMode  : Lan
    NumberOfPeers : 0
    
    --- 6. WiFi power saving (0 means off)
    
        Current AC Power Setting Index: 0x00000000
        Current DC Power Setting Index: 0x00000002
    --- 7. Errors
    
    Name                     : ProtonVPN
    ReceivedPacketErrors     : 0
    ReceivedDiscardedPackets : 0
    
    Name                     : WiFi
    ReceivedPacketErrors     : 0
    ReceivedDiscardedPackets : 0
  3. Select the whole report in your terminal and copy it.

  4. Open any free AI chat, paste this prompt, and put your report where it says.

    Prompt for any AI chat
    My internet is slow. Below is a report from my Windows PC: link speed, WiFi band and signal, how many networks are on each channel, DNS lookup time, Windows update sharing, WiFi power saving and adapter errors.
    
    Tell me in plain English what is wrong, most likely cause first, and the exact steps to fix each one. Say clearly if everything looks healthy and the problem is more likely my router or my internet provider.
    
    [paste the report here]
    Tip
    The report holds no passwords and no network names. It does show your network card model and the name of any VPN you run. If you'd rather not share those, delete those lines before you paste.
Checkpoint
You have a report with seven sections, and an AI has told you what it means.
If it breaksSection 2 and 3 are empty + 2 more
Section 2 and 3 are empty
You're on a wired connection or WiFi is off, so there's no WiFi to report. Section 1 is the one that matters for you.
Section 5 shows a red error
Some work or school PCs block that command. Skip it. You can check the same setting by hand in step 7.
Pasting does nothing
Right-click inside the terminal window, which also pastes, then press Enter.
Still stuck? Ask the community
STEP 06 of 07~3 min

Read the result: the six usual causes

Understand what each number means, so you can tell a real fault from a healthy reading.

    • 1. Link speed. On a cable, this should say 1 Gbps or more. 10 Mbps or 100 Mbps means a bad cable or port, which is exactly what the Reddit case had.
    • 2. WiFi band. 2.4 GHz reaches further but is slow and crowded. 5 GHz or 6 GHz is several times faster at close range. A signal under about 50% means you're too far from the router.
    • 3. Channel. If lots of networks share your channel, you all take turns. On 2.4 GHz, only channels 1, 6 and 11 don't overlap.
    • 4. DNS. This is the lookup that happens before any page loads. Under 50 ms is fine. If yours is much slower than 1.1.1.1, pages start slowly even on a fast line.
    • 5. Update sharing. Lan means Windows only shares updates with PCs in your home. Internet means it can upload them to strangers' PCs over your connection.
    • 6. Power saving. 0 is off. 1, 2 or 3 means Windows slows the WiFi card to save battery. The first line is for when you're plugged in, the second for battery.
  1. Our own result, as an example5 GHz at 82% signal, one network per channel, DNS at 33 ms, sharing limited to the home network and zero errors. That's a healthy connection. It flagged two things worth knowing: a VPN was running during the test, and WiFi power saving was on level 2 on battery.

    Tip
    Everything healthy but still slow? Then the fault is past your PC. Restart the router, test on a second device, and if both are slow next to the router, call your provider with your speed test numbers.
Checkpoint
You can point at the one or two lines in your report that are the problem, or say that your PC is healthy.
Stuck? Ask the community
STEP 07 of 07~4 min

Apply the fix, then test again

Make one change at a time and measure after each, so you know what worked.

Wired link at 10 or 100 Mbps

  • Replace the Ethernet cable with one marked Cat5e, Cat6 or Cat6a on the jacket.
  • Push both ends in until they click, and try a different port on the router.

On the 2.4 GHz band

  • In your WiFi list, connect to your router's 5 GHz network if it shows one. It often ends in 5G.
  • If your router uses one name for both bands, move closer and reconnect, or tell the WiFi card to prefer 5 GHz: open Device Manager, then Network adapters, double-click your WiFi card, open the Advanced tab and set Preferred Band to 5 GHz. The setting has that name on Intel cards and may be called something else on others.

A crowded channel

This one is changed on the router, not the PC. Open your router's settings page (the address and password are on its label), find the WiFi channel setting and pick the least crowded of 1, 6 or 11 for 2.4 GHz.

Slow DNS

Open Settings, then Network & internet, then WiFi or Ethernet, then Hardware properties. Next to DNS server assignment choose Edit, switch to Manual, turn on IPv4 and enter 1.1.1.1 and 1.0.0.1. This makes pages start faster. It doesn't raise your download speed.

Windows sharing updates

Open Settings, then Windows Update, then Advanced options, then Delivery Optimization, and turn off Allow downloads from other PCs.

WiFi power saving on battery

Paste these two lines into PowerShell. They set WiFi power saving to off when you're on battery. It uses a little more battery.

Windows PowerShell
powercfg /setdcvalueindex SCHEME_CURRENT 19cbb8fa-5279-450e-9fac-8a3d5fedd0c1 12bbebe6-58d6-4636-95bb-3217ef867c1a 0
powercfg /setactive SCHEME_CURRENT

Test again

  1. Run the same speed test as in step 2 and compare the three numbers.

    Tip
    What we tested. We ran every check in this course on our own PC and the report in step 5 is its real output. Our connection came back healthy, so we didn't need the fixes ourselves. They are standard Windows and router settings, and each one can be undone in the section at the end.
Checkpoint
You've made one change, run the speed test again, and written the new numbers next to the old ones.
If it breaksMy speed didn't change + 1 more
My speed didn't change
Undo that change and try the next cause on your list. If nothing on your PC is wrong, the fault is the router or the line, and your provider needs to fix it.
I can't find Preferred Band
Not every WiFi card has it. Connect to the 5 GHz network by name instead, or ask Claude for the setting name for your card model, which is in section 1 of your report.
Still stuck? Ask the community

Your first wins

It works. Now do something with it.

Check the rest of the house

Run the free check on every Windows PC at home. One device stuck on 2.4 GHz at the far end of the house can explain a lot.

Find what's using your connection

With Claude Code open, ask it which programs are sending and receiving the most data right now.

Prompt
Which programs on this PC are using the network most right now? Show me the top five in plain English and tell me what each one is. Don't close or change anything.

Get a better answer from your provider

If your PC is healthy and the line is slow, turn your numbers into a short, firm message.

Prompt
Write a short message to my internet provider. I pay for [your plan speed]. My speed tests next to the router, on two devices, show [your numbers]. Ask them to test the line and tell me what they'll do. Keep it polite and under 120 words.

Undo it cleanly

How to remove everything this mission installed.

The checks changed nothingClearing the DNS cache is the only thing the free check does, and Windows refills it as you browse.

DNSGo back to the same screen and set DNS server assignment to Automatic (DHCP).

Preferred BandSet it back to No Preference in the same Advanced tab.

Update sharingTurn Allow downloads from other PCs back on in the same screen.

WiFi power savingThese two lines put battery power saving back to the level our laptop had, level 2. Use the number your own report showed.

Windows PowerShell
powercfg /setdcvalueindex SCHEME_CURRENT 19cbb8fa-5279-450e-9fac-8a3d5fedd0c1 12bbebe6-58d6-4636-95bb-3217ef867c1a 2
powercfg /setactive SCHEME_CURRENT

Router channelSet the channel back to Auto on the router's settings page.

Next mission · Own your AIRun a ChatGPT-style AI on your own laptop
→