Meshtastic text radios (a pair of LoRa nodes)
Two small LoRa radios that pair with your phones over Bluetooth, so you can text each other with no mobile network, no Wi-Fi and no internet.
01When it saves you
In a long power cut the masts go quiet and your phone can't send a thing. With a Meshtastic node in each pocket, two people can still text each other across a neighbourhood, and messages hop through any other Meshtastic nodes nearby, including a repeater on your own roof. It keeps working for as long as the nodes have battery.
02How it works
LoRa (short for long range) is a way of sending small amounts of data very slowly, which lets a low-power radio reach much further than Bluetooth or Wi-Fi. Meshtastic is free, open-source software that runs on these radios and turns them into a texting network.
Your phone talks to your node over Bluetooth using the Meshtastic app. You type a message and the node sends it by radio. Any node that hears it passes it on (up to 3 hops by default), so messages can leapfrog round buildings and hills. On a private channel, messages are encrypted with a key only your group has.
In the UK it uses the licence-free 868 MHz band. Ofcom's rules allow up to 500 mW in the 869.4 to 869.65 MHz slot, but only for 10% of the time (the duty cycle: about 6 minutes of sending in any hour). Text messages are tiny, so a household never gets near that, and the firmware enforces it for you.
03What to buy
Credit-card sized, sealed against dust and rain (IP65), with GPS and a 700 mAh battery inside. It's a finished, cased device: charge it, pair it, set the region. Nothing to build or solder, so it's the easiest one to hand to a family member.
Where: The Pi Hut. Choose the **for Meshtastic** version, not the LoRaWAN one.
The board in our diagram. Very low power, so it also suits a solar node later, and it comes with Meshtastic installed plus LoRa and Bluetooth aerials. But it's a bare circuit board: you add a battery with the right plug and a case yourself.
Where: The RAKwireless store, or EU sellers that ship to the UK such as Hexaspot (UK VAT is charged at checkout on orders up to £135).
Avoid
- 915 MHz (American) or 433 MHz versions. In the UK buy the 868 MHz version, sometimes listed as EU868. Check the part number: DigiKey UK's cheap RAK starter kit with a "-9" in the part number is the 915 MHz one.
- The T1000-E for LoRaWAN. It looks the same and is sold next to the Meshtastic version, but it's a different product.
- Devices sold with MeshCore firmware. MeshCore runs on the same hardware but can't talk to Meshtastic nodes.
- Powering any LoRa board without its aerial screwed on. Transmitting into nothing can damage the radio chip.
- Listings that promise tens of kilometres as normal range. Those figures are mountain-top records.
04You’ll also need
- A smartphone for each person with the official Meshtastic app. Get it from the links on meshtastic.org ↗, not from a lookalike listing.
- A way to charge in a power cut: the T1000-E's magnetic USB charging cable (or its charging puck, about £15 at The Pi Hut) and a USB power bank.
- For the RAK kit only: a 3.7 V LiPo battery with a JST plug (check the polarity before plugging in) and a small case.
- A printed QR code of your private channel and a note of its name, kept with each node.
!Limits, honestly
- Text only, and slow. No voice calls and no internet.
- Range depends on height and what's in the way. Community tests report about 2 km between nodes in a built-up area with no line of sight, 1 to 3 km with better aerials, and only a few hundred metres in some inner-city tests. The 331 km record was between mountain tops.
- The T1000-E has no screen or keyboard. You need a working, charged phone to read and send.
- It only reaches other Meshtastic users on 868 MHz. It can't text a normal phone.
- The UK band allows 10% airtime. That's plenty for text, but a very busy mesh slows down.
- Anyone can read the default public channel. Keep names and addresses on your private channel.