Off-grid solar: Victron SmartSolar MPPT charge controller, panel and LiFePO4 battery
A solar panel, a smart charge controller and a 12 V lithium battery that keep radios, a laptop or a small home server running for as long as the sun comes up.
01When it saves you
A power station from the earlier module covers a day or two. If the grid is off for a week, or you want a radio station or a mesh node that never goes flat, you need a battery that refills itself. This setup runs 12 V kit directly, with no mains involved at all.
02How it works
The panel makes power when it's light. The charge controller sits between the panel and the battery and charges the battery at the right voltage. Your radios and other 12 V kit run from the battery, through fuses.
MPPT (maximum power point tracking) means the controller constantly adjusts to pull the most power the panel can give and converts any extra voltage into extra charging current. Victron says this harvests up to 30% more than a cheaper PWM controller, especially under changing cloud. In plain English: more charge from the same panel on a grey British day.
LiFePO4 (lithium iron phosphate) batteries are the safest common lithium type, last many more charge cycles than lead-acid, and you can use most of their capacity. A 12 V 100 Ah battery stores roughly 1.2 to 1.3 kWh (check the label of the one you buy).
03What to buy
The 100/50 takes up to 700 W of panels on a 12 V battery, so you can add panels later. It has Bluetooth for the free VictronConnect app, a LiFePO4 preset and a 98% peak efficiency. Example parts: Renogy 200 W panel (Renogy UK), Fogstar Drift 105 Ah or Drift ECO 100 Ah (Fogstar, UK).
Where: Controller: Cactus Navigation and other Victron dealers. Panel: Renogy UK. Battery: Fogstar.
Plenty for one panel of up to about 290 W on a 12 V battery, and it adds a load output that switches loads off before the battery goes too flat. You lose room to grow.
Where: Cactus Navigation
Avoid
- No-name "MPPT" controllers that are really PWM inside. Buy a known brand from a real dealer.
- Lithium batteries without a built-in battery management system (BMS) or low-temperature charge protection: charging LiFePO4 below freezing damages it. If yours can't block cold charging, use Victron's low-temperature cut-off with a Smart Battery Sense.
- Panels whose open-circuit voltage (Voc, on the label) could exceed 100 V. That is the 100/50's absolute limit, and wiring several panels in series adds up quickly.
- Cheap all-in-one "solar kits" with a PWM controller and a lead-acid battery: less charge and a shorter life.
04You’ll also need
- A battery fuse between the battery and controller: Victron specifies 55 to 70 A for the 100/50 (35 to 40 A for the 100/30), as close to the battery positive as possible, with a matching fuse holder (check current price).
- A separate smaller fuse for each piece of kit you run from the battery, sized for that device and its cable.
- A way to disconnect the panel: a PV isolator switch or breaker, or an in-line fuse you can pull.
- Flexible multi-strand copper cable thick enough for the fuse rating (the 100/50 terminals take up to 16 mm²), MC4 extension leads from the panel, and lugs.
- A multimeter to check polarity and voltages before you connect anything.
!Limits, honestly
- UK winter sun is weak and short. A panel that runs everything in June may barely keep up with a radio on standby in December; size for winter, not summer.
- The 100/50 has no load output, so loads go straight to the battery: make sure your battery's BMS disconnects before it goes completely flat.
- The full rated output holds only up to 40 °C, and the 100 V panel voltage limit is absolute.
- Batteries store a lot of energy. A short circuit without a fuse can start a fire. Fuse every positive cable at the battery end.